K20C Ported Head Comparison
Dyno-tested and proven results
Compare a stock K20C1 cylinder head with three ported cylinder head types.
| Published detail | Stock Cylinder Head | Pocket Ported (sometimes called stock port) | Full Ported | Full Race Ported |
|---|---|---|---|---|
| Descriptor | True, untouched stock cylinder head | Sometimes called stock port; only the bowls are modified | Dividers reshaped and blended to the bowls; exhaust outlet opened; exhaust micropolish is sometimes included | Larger than the full port; great for 64 mm and larger turbos; always includes exhaust micropolish |
| Peak-power RPM range | 6,000–7,200 rpm | 7,200–8,000 rpm | 7,600–8,500 rpm | 7,800–9,000 rpm |
| Cold-start manners (overnight; 1–10) | 10 (stock baseline) | 9 | 7–8 (Hondata); 8–9 (Motec) | 7–7.5 (Hondata); 8.5 (Motec) |
| Spool improvement | Baseline; no improvement | 400–600 rpm better spool | 500–800 rpm better spool | 500–800 rpm better spool |
| Drop-in turbo power rating | 4–5 | 7–10 | 6.5–9; not recommended for MHI Stage 2 or normal Kuro | 7; still provides gains, but is better suited to full-frame setups |
| Full-frame turbo power rating | 5–6 | 7–9 | 7–10 | 8–10 |
| Roll-racing rating | 1–5 | 7–10 | 7–9 | 7–8 |
| Spool / lag response rating | Drop-in: 3–5; full-frame: 1–5 to 2–5 | Drop-in: 9–10; full-frame: 9 | Drop-in: 9–10; full-frame: 9–10 | Drop-in: 9–10; full-frame: 9–10 |
| Boost reduction with camshafts for equivalent power | 2–5 psi reduction | 5–7 psi with stock camshafts; 6–11 psi with camshafts | Typically 5–11 psi; 6–10 psi with stock cams, 10–18 psi with camshafts | Typically 5–11 psi; 6–10 psi with stock cams and 10–18 psi with camshafts |
| Boost pressure with camshafts at stated power | Over 40 psi at 700 WHP | 35–36 psi at 700 WHP | 32 psi at 700 WHP | 32 psi at 800 WHP |
| Peak-power capability rating | 3–5 | 8 | 9 | 10 |
| Estimated peak power | 700 WHP | 600–800 WHP | 600–1,000 WHP | 1,000+ WHP |
| Exhaust-port finish / outlet notes | Not stated | Exhaust outlet flange diameter is a limiting factor | Micro-polish through the internal exhaust area and pockets; outlet enlarged to match V-band flange volume | Full polish through the internal exhaust area and pockets; outlet enlarged to match V-band flange volume |
| Limiting factor | Intake port flow is lower than exhaust port flow | Exhaust outlet flange diameter | Intake port size limits the usable RPM range | Dependent on turbo size |
| Backpressure Lower is better | 7 Lower is better | 6 Lower is better | 3 Lower is better | 1 Lower is better |
How to read the ratings
The 1–10 scores and power/RPM figures are the product descriptions and estimates relative to the stock head, not independent test guarantees. The product pages note that results depend on turbo size, fuel, compression, and setup. Estimates are based on a heavy-roller Dynojet; results may differ across dyno types.
Before ordering: Please check the ported head page for your RPM range and turbo selection so we can better tailor your cylinder head to maximize your gains.
